Cloisonné Enamel

Why Does Cloisonné Enamel Sink After Firing?

See why packed enamel settles as it fuses, how to check a cooled cell, and when to refill or pause.

By BeenEast Editorial · Published · Reviewed

Why the glass sits lower after firing

Glass grains soften and fuse in the kiln, filling the spaces between them. A cell that looked full before firing can end up below the wire tops. Once it cools, ask your instructor whether to refill if the enamel is intact and the wire is stable. If you find a crack, a loose flake, or a shifted wire, check what happened before deciding whether the piece should go back in the kiln.

Sources: Jean Tudor · The Art of Enameling: Cloisonné, student working outline · Thompson Enamel · Enameling Help and Information

Follow one cell from grains to glass

Wet packing uses water to carry glass grains into the cell. Drying removes the water, leaving spaces between the dry grains. In the kiln, the softened glass fills those spaces, so the enamel layer sits lower. The first drawing shows dry grains before firing. All three drawings use the same wire tops as a reference.

Sources: Miranda Andersen / Pocosin Arts · Introduction to Cloisonné Enameling · Woodrow W. Carpenter · Intro to Enameling: Cloisonné Pendant · Jean Tudor · The Art of Enameling: Cloisonné, student working outline

Separated blue grains inside a cell beneath a dashed line at the wire tops
Dry grains before firing. The drawing exaggerates the gaps between the grains.

Check that the wire is still a reliable reference

Compare the joins and the exposed wire height with a photo or sketch made before filling. If a join has opened or a strip has shifted, check the attachment first. In the base-coat method, an overly thick base coat can let the wire sink. If the wire height has changed, the gap between the wire and the glass cannot tell you how far the enamel settled.

Sources: Jean Tudor · The Art of Enameling: Cloisonné, student working outline

If color crosses a boundary, look for when it first appeared. Too much water during filling can carry grains into the next cell. A photo taken only after firing cannot tell you when the grains crossed.

Sources: Woodrow W. Carpenter · Intro to Enameling: Cloisonné Pendant

Read the cooled cell before you refill

After cooling, inspect the same cell under the same light and from the same angle. Check the wire first, then record the glass level against the wire tops. Note separately whether the surface is intact and whether color has crossed a boundary. A low cell with intact glass calls for a different response from a low cell with a loose edge.

Sources: Thompson Enamel · Enameling Help and Information

A continuous blue glass layer below the wire tops, with a double-headed arrow showing the gap
The same cell after cooling. The gap below the wire tops is exaggerated to make it easier to see.

Refill for the finish you want

In Pocosin Arts’ level-polished exercise, repeated filling and firing build the glass up to the wire tops. Ask your instructor which intact low areas need more enamel. Grinding removes high spots and cannot fill a depression. A raised finish has a different target.

Sources: Miranda Andersen / Pocosin Arts · Introduction to Cloisonné Enameling · Jean Tudor · The Art of Enameling: Cloisonné, student working outline

Pale grains resting on the solid blue glass layer below the dashed wire-top reference
New grains sit on the fired glass. After firing and cooling again, check the level against the same wire tops.

Dry the new fill as directed and have your instructor guide the next firing. After cooling, check the same cell against the same wire tops.

Sources: Miranda Andersen / Pocosin Arts · Introduction to Cloisonné Enameling

Pause for a crack, a loose patch, or moved wire

Fusing lowers the fill. Cracking or lifting can involve stress as the piece cools. Differences in how metal and glass contract, uneven layers, and the choice of materials can all affect the result. The surface alone cannot establish the cause.

Sources: Jean Tudor · The Art of Enameling: Cloisonné, student working outline · Thompson Enamel · Enameling Help and Information

Before refilling, mark the spot and compare it with earlier photos. Then review the wire, grain placement, and drying. Finally, check the metal, enamel, and firing records with your instructor against the studio’s instructions. Once you have checked the problem, decide together whether to try again.

Sources: Thompson Enamel · Enameling Help and Information

Make the next sample answer one question

If the same end of an intact cell keeps turning out low, make another sample with your instructor. Keep the pattern, materials, and firing plan the same and change only how evenly you spread the grains. Once it cools, compare that end against the same wire reference. A smaller difference suggests that grain placement may affect the result in this setup. Check separately if you change the metal or enamel.

Sources: Thompson Enamel · Enameling Help and Information

Continue reading

References

Jean Tudor · The Art of Enameling: Cloisonné, student working outline

Thompson Enamel · Enameling Help and Information

Miranda Andersen / Pocosin Arts · Introduction to Cloisonné Enameling

Woodrow W. Carpenter · Intro to Enameling: Cloisonné Pendant

Back to all guides